Added MeshPoE-S3 board

Boards.h

@@ -158,10 +158,6 @@
     #endif
   #endif
 
-  #define LORA_PA_UNKNOWN  0x00
-  #define LORA_PA_GC1109   0x01
-  #define LORA_PA_KCT8103L 0x02
-
   #define HAS_DISPLAY false
   #define HAS_BLUETOOTH false
   #define HAS_BLE false
@@ -457,7 +453,7 @@
         #define HAS_TCXO true
         #define HAS_BUSY true
         #define DIO2_AS_RF_SWITCH true
-        #define OCP_TUNED 0x28
+        #define OCP_TUNED 0x18
         const int pin_busy = 32;
         const int pin_dio = 33;
         const int pin_tcxo_enable = -1;
@@ -563,7 +559,7 @@
       #define HAS_SLEEP true
       #define PIN_WAKEUP GPIO_NUM_0
       #define WAKEUP_LEVEL 0
-      #define OCP_TUNED 0x28
+      #define OCP_TUNED 0x18
 
       const int pin_btn_usr1 = 0;
 
@@ -605,9 +601,8 @@
       #define HAS_LORA_LNA true
       #define PIN_WAKEUP GPIO_NUM_0
       #define WAKEUP_LEVEL 0
-      #define OCP_TUNED 0x28
+      #define OCP_TUNED 0x38
       #define Vext GPIO_NUM_36
-      #define LORA_PA_MODEL LORA_PA_UNKNOWN;
 
       const int pin_btn_usr1 = 0;
 
@@ -629,17 +624,19 @@
 
       #define LORA_LNA_GAIN  17
       #define LORA_LNA_GVT   12
+      #define LORA_PA_GC1109 true
+      #define LORA_PA_AUTO_DETECT true
       #define LORA_PA_PWR_EN  7
-      #define LORA_PA_CSD     2 // Same pin on GC1109
-      #define LORA_PA_CPS    46 // Same pin on GC1109
-      #define LORA_PA_CTX     5 // Only used on KCT8103
 
-      #define PA_MAX_OUTPUT  28
+      #define LORA_PA_CSD     2  // GC1109: PA_EN | KCT8103L: CSD (same pin, different pull resistor)
-      #define PA_GAIN_POINTS 22
+      #define LORA_PA_CTX     5  // KCT8103L: TX/LNA select (CTX=LOW=LNA, CTX=HIGH=PA)
+      #define LORA_PA_CPS    46  // GC1109: TX_EN
 
-      #define LORA_LNA_KCT8103L_GAIN 21
+      #define PA_MAX_OUTPUT          28
-      const int PA_GC1109_VALUES[PA_GAIN_POINTS] =   {11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 10, 10,  9, 9, 8, 7};
+      #define PA_GAIN_POINTS         22
-      const int PA_KCT8103L_VALUES[PA_GAIN_POINTS] = {13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 12, 12, 11, 11, 10, 9, 8, 7};
+      #define PA_GC1109_GAIN_VALUES   11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 10, 10, 9, 9, 8, 7
+      #define PA_KCT8103L_GAIN_VALUES 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 13, 12, 12, 11, 11, 10, 9, 8, 7
+      #define PA_GAIN_VALUES PA_KCT8103L_GAIN_VALUES // compile-time fallback; runtime detection selects correct table
 
       const int pin_cs = 8;
       const int pin_busy = 13;
@@ -828,7 +825,7 @@
       #define DIO2_AS_RF_SWITCH true
       #define HAS_BUSY true
       #define HAS_TCXO true
-      #define OCP_TUNED 0x28
+      #define OCP_TUNED 0x18
 
       #define HAS_DISPLAY true
       #define HAS_CONSOLE true
@@ -1240,7 +1237,7 @@
   // Default OCP value if not specified
   // in board configuration
   #ifndef OCP_TUNED
-    #define OCP_TUNED 0x28
+    #define OCP_TUNED 0x38
   #endif
 
   #ifndef NP_M

Config.h

@@ -20,7 +20,7 @@
 	#define CONFIG_H
 
 	#define MAJ_VERS  0x01
-	#define MIN_VERS  0x56
+	#define MIN_VERS  0x55
 
 	#define MODE_HOST 0x11
 	#define MODE_TNC  0x12

Console/build.py

@@ -4,10 +4,10 @@ import sys
 import shutil
 
 packages = {
-    "rns": "rns-1.1.9-py3-none-any.whl",
+    "rns": "rns-1.0.3-py3-none-any.whl",
-    "nomadnet": "nomadnet-0.9.11-py3-none-any.whl",
+    "nomadnet": "nomadnet-0.9.1-py3-none-any.whl",
-    "lxmf": "lxmf-0.9.6-py3-none-any.whl",
+    "lxmf": "lxmf-0.9.3-py3-none-any.whl",
-    "rnsh": "rnsh-0.1.9-py3-none-any.whl",
+    "rnsh": "rnsh-0.1.5-py3-none-any.whl",
 }
 
 DEFAULT_TITLE = "RNode Bootstrap Console"
@@ -194,29 +194,8 @@ def optimise_manual(path):
         ("_images/meshchat_1.webp", pm),
         ("_images/radio_is5ac.png", pm),
         ("_images/radio_rblhg5.png", pm),
-        ("_images/rbrowser.webp", pm),
-        ("_images/rnphone.webp", pm),
-        ("_images/retibbs.webp", pm),
-        ("_images/meshchatx.webp", pm),
-        ("_images/lxst_phone.webp", pm),
-        ("_images/columba.webp", pm),
         ("_static/rns_logo_512.png", 256),
         ("../images/bg_h_1.webp", pm),
-
-        ("../../images/3_conv.webp", pm/2),
-        ("../../images/an1.webp", pm/2),
-        ("../../images/bg1ds1.webp", pm/2),
-        ("../../images/bg1ds2.webp", pm/2),
-        ("../../images/bg_h_1.webp", pm/2),
-        ("../../images/bg_h_2.webp", pm/2),
-        ("../../images/g1p.webp", pm/2),
-        ("../../images/g2p.webp", pm/2),
-        ("../../images/g3p.webp", pm/2),
-        ("../../images/g4p.webp", pm/2),
-        ("../../images/lora_rnodes.webp", pm/2),
-        ("../../images/nn_an.webp", pm/2),
-        ("../../images/nn_conv.webp", pm/2),
-        ("../../images/nn_init.webp", pm/2),
     ]
 
     import subprocess

Display.h

@@ -1154,7 +1154,6 @@ void update_display(bool blank = false) {
 
       #if BOARD_MODEL == BOARD_HELTEC_T114
         display.clear();
-        digitalWrite(PIN_T114_TFT_BLGT, LOW);
       #elif BOARD_MODEL != BOARD_TDECK && BOARD_MODEL != BOARD_TECHO
         display.clearDisplay();
       #endif

Makefile

@@ -30,6 +30,7 @@ prep: prep-avr prep-esp32 prep-samd
 prep-avr:
 	arduino-cli core update-index --config-file arduino-cli.yaml
 	arduino-cli core install arduino:avr --config-file arduino-cli.yaml
+	arduino-cli core install unsignedio:avr --config-file arduino-cli.yaml
 
 prep-esp32:
 	arduino-cli core update-index --config-file arduino-cli.yaml

Utilities.h

@@ -1336,33 +1336,17 @@ int getTxPower() {
 }
 
 #if HAS_LORA_PA
-    #if BOARD_MODEL == BOARD_HELTEC32_V4
+  #if LORA_PA_AUTO_DETECT
-	bool pa_values_determined = false;
+    static const int gc1109_tx_gain[PA_GAIN_POINTS]   = {PA_GC1109_GAIN_VALUES};
-	int tx_gain[PA_GAIN_POINTS] = {100};
+    static const int kct8103l_tx_gain[PA_GAIN_POINTS] = {PA_KCT8103L_GAIN_VALUES};
-    #else
+    const int* tx_gain = sx126x_modem.isKCT8103L() ? kct8103l_tx_gain : gc1109_tx_gain;
-	bool pa_values_determined = true;
+  #else
-	const int tx_gain[PA_GAIN_POINTS] = {PA_GAIN_VALUES};
+    const int tx_gain[PA_GAIN_POINTS] = {PA_GAIN_VALUES};
-    #endif
+  #endif
 #endif
 
-extern uint8_t lora_pa_model;
-void determine_pa_values() {
-	#if BOARD_MODEL == BOARD_HELTEC32_V4
-		if (lora_pa_model == LORA_PA_GC1109) {
-			for (int i=0; i < PA_GAIN_POINTS; i++) { tx_gain[i] = PA_GC1109_VALUES[i]; }
-			pa_values_determined = true;
-			for (int i=0; i < PA_GAIN_POINTS; i++) { Serial.print(" "); Serial.printf("%d", tx_gain[i]); }
-		} else if (lora_pa_model == LORA_PA_KCT8103L) {
-			for (int i=0; i < PA_GAIN_POINTS; i++) { tx_gain[i] = PA_KCT8103L_VALUES[i]; }
-			pa_values_determined = true;
-			for (int i=0; i < PA_GAIN_POINTS; i++) { Serial.print(" "); Serial.printf("%d", tx_gain[i]); }
-		}
-	#endif
-}
-
 int map_target_power_to_modem_output(int target_tx_power) {
 	#if HAS_LORA_PA
-		if (!pa_values_determined) { determine_pa_values(); }
 		int modem_output_dbm = -9;
 		for (int i = 0; i < PA_GAIN_POINTS; i++) {
 			int gain = tx_gain[i];

arduino-cli.yaml

@@ -4,3 +4,7 @@ board_manager:
   - https://raw.githubusercontent.com/RAKwireless/RAKwireless-Arduino-BSP-Index/main/package_rakwireless_index.json
   - https://github.com/HelTecAutomation/Heltec_nRF52/releases/download/1.7.0/package_heltec_nrf_index.json
   - https://adafruit.github.io/arduino-board-index/package_adafruit_index.json
+## proMicro
+# - https://raw.githubusercontent.com/pdcook/nRFMicro-Arduino-Core/main/package_nRFMicro_index.json #can't use it bc the name has spaces, i created the file below
+  - https://gist.githubusercontent.com/gargomoma/b5cffc40e5df88462f2b488492feb6ca/raw/198c5706289014dd64be31607495e02f056d52a3/nrf_cli_fix.json
+  - https://files.seeedstudio.com/arduino/package_seeeduino_boards_index.json

sx126x.cpp

@@ -96,14 +96,6 @@
   #define SPI spiModem
 #endif
 
-#if HAS_LORA_PA
-  uint8_t lora_pa_model = LORA_PA_MODEL;
-#endif
-
-#if HAS_LORA_LNA
-  int lora_lna_gain = LORA_LNA_GAIN;
-#endif
-
 extern SPIClass SPI;
 
 #define MAX_PKT_LENGTH 255
@@ -282,21 +274,6 @@ void sx126x::setPacketParams(long preamble_symbols, uint8_t headermode, uint8_t
   buf[7] = 0x00; 
   buf[8] = 0x00; 
   executeOpcode(OP_PACKET_PARAMS_6X, buf, 9);
-
-  // SX1262 errata section 15.4: IQ polarity is inverted compared to
-  // SX1276. The SetPacketParams command resets register 0x0736 to an
-  // incorrect default. For standard IQ (no inversion), bit 2 must be
-  // SET after every SetPacketParams call. For inverted IQ, bit 2 must
-  // be CLEARED. Without this fix, LoRa RX demodulation fails silently
-  // while TX continues to work.
-  uint8_t iqreg = readRegister(0x0736);
-  if (buf[5] == 0x00) {
-    // Standard IQ: set bit 2
-    writeRegister(0x0736, iqreg | 0x04);
-  } else {
-    // Inverted IQ: clear bit 2
-    writeRegister(0x0736, iqreg & ~0x04);
-  }
 }
 
 void sx126x::reset(void) {
@@ -396,66 +373,30 @@ int sx126x::begin(long frequency) {
   setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
 
   #if HAS_LORA_PA
-    if (lora_pa_model == LORA_PA_UNKNOWN) {
+    #if LORA_PA_AUTO_DETECT
-      #if BOARD_MODEL == BOARD_HELTEC32_V4
+      // Power up the FEM, then read GPIO LORA_PA_CSD as input.
-        
+      // The V4.2 (GC1109) board pulls it LOW; V4.3 (KCT8103L) pulls it HIGH.
-        pinMode(LORA_PA_PWR_EN, OUTPUT);
-        pinMode(LORA_PA_CSD, INPUT);
-        digitalWrite(LORA_PA_PWR_EN, HIGH); delay(5);
-        if (digitalRead(LORA_PA_CSD) == HIGH) {
-          lora_pa_model = LORA_PA_KCT8103L;
-          lora_lna_gain = LORA_LNA_KCT8103L_GAIN;
-        } else {
-          lora_pa_model = LORA_PA_GC1109;
-        }
-      #endif
-    }
-
-    if (lora_pa_model == LORA_PA_GC1109) {
-      // Enable Vfem_ctl for supply to
-      // PA power net.
       pinMode(LORA_PA_PWR_EN, OUTPUT);
       digitalWrite(LORA_PA_PWR_EN, HIGH);
+      delay(1);
+      pinMode(LORA_PA_CSD, INPUT);
+      delay(1);
+      _kct8103l = (digitalRead(LORA_PA_CSD) == HIGH);
 
-      // Enable PA LNA and TX standby
+      if (_kct8103l) {
-      pinMode(LORA_PA_CSD, OUTPUT);
+        // KCT8103L (V4.3): CSD=HIGH enables chip, CTX=LOW=LNA/RX, CTX=HIGH=PA/TX
-      digitalWrite(LORA_PA_CSD, HIGH);
+        pinMode(LORA_PA_CSD, OUTPUT);
-
+        digitalWrite(LORA_PA_CSD, HIGH);
-      // Keep PA CPS low until actual
+        pinMode(LORA_PA_CTX, OUTPUT);
-      // transmit. Does it save power?
+        digitalWrite(LORA_PA_CTX, LOW); // LNA enabled by default
-      // Who knows? Will have to measure.
+      } else {
-      // Note from the future: Nope.
+        // GC1109 (V4.2): PA_EN=HIGH enables chip, CPS=HIGH=full PA mode
-      // Power consumption is the same,
+        pinMode(LORA_PA_CSD, OUTPUT);
-      // and turning it on and off is
+        digitalWrite(LORA_PA_CSD, HIGH);
-      // not something that it likes.
+        pinMode(LORA_PA_CPS, OUTPUT);
-      // Keeping it high for now.
+        digitalWrite(LORA_PA_CPS, HIGH);
-      pinMode(LORA_PA_CPS, OUTPUT);
+      }
-      digitalWrite(LORA_PA_CPS, HIGH);
+    #endif
-
-      // On Heltec V4, the PA CTX pin
-      // is driven by the SX1262 DIO2
-      // pin directly, so we do not
-      // need to manually raise this.
-
-    } else if (lora_pa_model == LORA_PA_KCT8103L) {
-      // Enable Vfem_ctl for supply to
-      // PA power net.
-      pinMode(LORA_PA_PWR_EN, OUTPUT);
-      digitalWrite(LORA_PA_PWR_EN, HIGH);
-
-      // Enable KCT8103L chip
-      pinMode(LORA_PA_CSD, OUTPUT);
-      digitalWrite(LORA_PA_CSD, HIGH);
-
-      // Enable receive LNA
-      pinMode(LORA_PA_CTX, OUTPUT);
-      digitalWrite(LORA_PA_CTX, LOW);
-
-      // On Heltec V4.3, the PA CPS pin
-      // is driven by the SX1262 DIO2
-      // pin directly, so we do not
-      // need to manually raise this.
-    }
   #endif
 
   return 1;
@@ -465,15 +406,13 @@ void sx126x::end() { sleep(); SPI.end(); _preinit_done = false; }
 
 int sx126x::beginPacket(int implicitHeader) {
   #if HAS_LORA_PA
-    if (lora_pa_model == LORA_PA_GC1109) {
+    #if LORA_PA_AUTO_DETECT
-      // Enable PA CPS for transmit
+      if (_kct8103l) {
-      // digitalWrite(LORA_PA_CPS, HIGH);
+        // CTX=HIGH: switch KCT8103L to PA/TX mode.
-      // Disabled since we're keeping it
+        digitalWrite(LORA_PA_CTX, HIGH);
-      // on permanently as long as the
+      }
-      // radio is powered up.
+      // GC1109: CPS kept HIGH permanently, no action needed.
-    } else if (lora_pa_model == LORA_PA_KCT8103L) {
+    #endif
-      digitalWrite(LORA_PA_CTX, HIGH);
-    }
   #endif
 
   if (_txen != -1) { digitalWrite(_txen, HIGH); } //Set TXen high when transmitting
@@ -566,7 +505,7 @@ int ISR_VECT sx126x::currentRssi() {
   executeOpcodeRead(OP_CURRENT_RSSI_6X, &byte, 1);
   int rssi = -(int(byte)) / 2;
   #if HAS_LORA_LNA
-    rssi -= lora_lna_gain;
+    rssi -= LORA_LNA_GAIN;
   #endif
   return rssi;
 }
@@ -582,7 +521,7 @@ int ISR_VECT sx126x::packetRssi() {
   executeOpcodeRead(OP_PACKET_STATUS_6X, buf, 3);
   int pkt_rssi = -buf[0] / 2;
   #if HAS_LORA_LNA
-    pkt_rssi -= lora_lna_gain;
+    pkt_rssi -= LORA_LNA_GAIN;
   #endif
   return pkt_rssi;
 }
@@ -689,17 +628,13 @@ void sx126x::onReceive(void(*callback)(int)){
 
 void sx126x::receive(int size) {
   #if HAS_LORA_PA
-    if (lora_pa_model == LORA_PA_GC1109) {
+    #if LORA_PA_AUTO_DETECT
-      // Disable PA CPS for receive
+      if (_kct8103l) {
-      // digitalWrite(LORA_PA_CPS, LOW);
+        // CTX=LOW: switch KCT8103L to LNA/RX mode.
-      // That turned out to be a bad idea.
+        digitalWrite(LORA_PA_CTX, LOW);
-      // The LNA goes wonky if it's toggled
+      }
-      // on and off too quickly. We'll keep
+      // GC1109: CPS kept HIGH permanently, no action needed.
-      // it on permanently, as long as the
+    #endif
-      // radio is powered up.
-    } else if (lora_pa_model == LORA_PA_KCT8103L) {
-      digitalWrite(LORA_PA_CTX, LOW);
-    }
   #endif
 
   if (size > 0) {
@@ -841,17 +776,7 @@ void sx126x::handleLowDataRate() {
 }
 
 // TODO: Check if there's anything the sx1262 can do here
-// SX1262 errata section 15.1: Modulation quality with 500 kHz LoRa BW.
+void sx126x::optimizeModemSensitivity(){ }
-// Register 0x0889 bit 2 must be cleared for 500 kHz, set for all other
-// bandwidths. Improves receiver sensitivity at non-500 kHz bandwidths.
-void sx126x::optimizeModemSensitivity(){
-  uint8_t reg = readRegister(0x0889);
-  if (getSignalBandwidth() == 500E3) {
-    writeRegister(0x0889, reg & 0xFB); // clear bit 2
-  } else {
-    writeRegister(0x0889, reg | 0x04); // set bit 2
-  }
-}
 
 void sx126x::setSignalBandwidth(long sbw) {
   if (sbw <= 7.8E3)        { _bw = 0x00; }